Greystone, if you ever get the username/password prompt, one of the tick boxes on there will be about connecting automatically. If you never see the password prompt you can always force it to display by removing the password from Tools/Internet Options/Connections tab/Settings, and reconnecting.

Greystone

To display password prompt.

Go into properties for the dial up connection, select Options tab (2nd tab) "Prompt for Name and password..." is the 2nd check box down.

Spaceman, no problem, I find many of the trojan/sypware/virus checker produce the odd false positive; some because their definitions are not spot on and others to try to con you into paying for something (these are the ones I avoid at all costs).

I may not use the full range of checkers much now but each of them produced loads of hits when I first ran them on my PCs so Im still happy to recommend them all to uses who have serious PC problems.

Neil

Kayak/Spaceman/anyone, help!

My lap top fell of the sofa and has done some damage to the little socket (attached to mother board) where the power cable plugs into.

I took the lap top apart and finally got to the MB, looked underneath and sure enough there is a little black conector whch has fallen off. I put it back on as best I can (just pushed it), put the lap top back together and tried it it.

First of all I'm amazed it fires up at all after I had it in bits. Then I proceed to try and insert the power cable, volia, it works for a few seconds then cuts out (the power supply). After a little fiddle it comes back on but now has gone again.

Are these components attached with a soldering iron? (it seems attached with a silver substance) If so can I just try and do it myself? Or any other ideas? i.e. can I glue it on or does it need to conduct somehow?

thanks!

Mr Euro. they differ from PC to PC but I would guess its soldered, You have probably already broken the warranty by opening it, so I would definatly have a go with the soldering Iron (but I am pretty used to soldering !!!). Try and find where the break is before soldering. Gently flex the part and see if you can see the break, it could be that the break is not exactly where you expect, it might be on the mobo tracks near the socket, if it is its a bit harder to solder and you will probably have to scrape some lacquer off the track before solding a link across the break.

Thanks Spaceman.

In fact it's really strange and I cannot understand how it works. The little black box (connector) is plastic and yet is soldered on to the motherboard just with 3 little dabs of solder. What I don't inderstand is how does it conduct the power into the mother board? It can't be through the solder as it doesn;t conduct through plastic? I think the solder is only there to stick it to the mother board? I can't recall any tracks but perhaps there were?

Do you think I could super glue it on?

Thanks!

Mr Euro, the conductors will be going through holes in the motherboard to end in the blobs of solder.

To be honest I think it may be the socket itself that's misshapen rather than the soldering to the motherboard.

hi Kayak, no I'm sure it's the soldering thats broken, the connector is fine. But how does it conduct through plastic? This is what I don't understand? I am tempted to try and super glue it but will await yours/Spacemans guidance! Else it's a trip to the electrical repair shop!

It can't conduct through plastic. Either the conductors go from the bottom of the socket through holes in the motherboard and are soldered from the other side, or they go out sideways on the same side of the motherboard and are soldered there. You can't solder onto plastic so if you see solder on the socket there must be a bit of metal there.

If you do try to fix it, wipe your soldering iron on a damp sponge to ensure the solder you try to put on is clean and be very very quick or otherwise the heat will conduct to the plastic socket and melt it faster than you can say "I shouldn't mess with things I don't understand." :-)

Mr E,

Have a look at the your contents insurance if its new for old take advantage:-)

Will have a look mega!

Kayak, there are dabs of solder still on the motherboard, do you think if I put the connector onto them and super glue around the connector (to the motherboard), it will still work?

No, you would definitely need to solder the connectors of the socket on.

ok thanks. Here I go for round 2...........

Mr E

If you have to ask these questions then I doubt you are good enough at soldering. Take it to your local repair shop.

Mr Euro, I'm no expert on the innerds of laptops, but the big danger with soldering youself is whether the heat will damage any of the nearby components! Just a thought.

I agree with Optimist & S C. Do not solder this yourself! You can/will do a lot more damage. The secret of soldering is a VERY hot iron and speed of hand plus heat sinks. If this is your first time this is not the item to practice on.

Edit : I also used 'Zap' straps (in my earlier days as a circuit board repairer for BT) to earth myself in case I touched sensative component parts and caused 'tracking'. I wonder if that's still the case nowadays with you young whipper-snappers?

I will take your good advice and not touch it myself.

However, during the interim period (i.e. this morning!) I decided to try and super glue it to the board (as the base is just plastic) and have it try and conduct through the two (should be three) bits of solder that are there. Doesn't seem to be working. Now I need to take it apart again and hope can get the component off the motherboard!

Doh!

Mr E

If the plug is glued and/or half soldered you could damage it more. Take it to your local repair shop.

Quickly!

;-0