Sharesmagazine
 Home   Log In   Register   Our Services   My Account   Contact   Help 
 Stockwatch   Level 2   Portfolio   Charts   Share Price   Awards   Market Scan   Videos   Broker Notes   Director Deals   Traders' Room 
 Funds   Trades   Terminal   Alerts   Heatmaps   News   Indices   Forward Diary   Forex Prices   Shares Magazine   Investors' Room 
 CFDs   Shares   SIPPs   ISAs   Forex   ETFs   Comparison Tables   Spread Betting 
You are NOT currently logged in
 
Register now or login to post to this thread.

PC & MAC CLINIC - On line problem solving. (CPU)     

Crocodile - 16 Dec 2002 03:59

Iain - 07 Feb 2004 13:29 - 1297 of 11003

I want to Install a New Hard Drive.How do I Copy my hard drive onto a new one?

Big Al - 07 Feb 2004 14:24 - 1298 of 11003

Rick

Not sure if the NTL setup is similar to the USB broadband modem I use, but I also have a dialup modem in the same computer as backup if broadband fails. I then simply change the default connection I want and dialup on my secondary phone line.

In theory therefore it should be very simple and there is no conflict.

Hil - I bet your hubby's in trouble! ;-)

Mega Bucks - 07 Feb 2004 14:28 - 1299 of 11003

Thanks everyone for all your help will install later and keep you posted :-)

leedslad - 07 Feb 2004 16:34 - 1300 of 11003

help
I am running xp pro with 2.5 proceser and 1gig ddr400 ram. my problem is when i have 2 level 2 windows open if i try to open a third it opens but the screen opens but with no trades or prices. if i close one of the other ones it starts straight away. Any ideas please

2Abbey - 08 Feb 2004 09:16 - 1301 of 11003

Thinking of increasing the memory on my PC.

Currently use 512MB DDR 400. I believe there was a little suffix after the memory description of 2.5, I think this refers to the "latency" of the memory.

My question is do I have to match this 2.5 figure on the new memory stick, or would any stick of 512MB DDR400 do?

What would be the possible effects of using memeory from different manufacturers etc?

Thanks in advance.

Spaceman - 08 Feb 2004 09:53 - 1302 of 11003

2Abbey, you need 2.5 CAS or better but most will meet that spec, you should be fine to mix different manufacturers so long as it it some or higher spec however check your PC motherboard instructions as some do have limitations on mix and match.

2Abbey - 08 Feb 2004 10:03 - 1303 of 11003

Thanks Spaceman

Iain - 08 Feb 2004 15:08 - 1304 of 11003

Anyone Know how to copy files to New Hard drive?

Optimist - 08 Feb 2004 15:48 - 1305 of 11003

Iain are you trying to copy your entire system to the new hard drive?

If you are then check out programs such as Norton Ghost which I believe will sort you although I have not used it myself.

If you just want to transfer data then you could use Xcopy from the command prompt. I have also used this to transfer an entire system but you have to first make the new disk bootable and then mount both disks as secondary drives on a different system.

Once you have transfered your system keep the old disk in a safe place. You never know when it will come in useful if you get a problem on the new disk. Also, make sure that your new disk uses NTFS file system.

Timeliner - 09 Feb 2004 08:21 - 1306 of 11003

Just switched on spare PC this morning.
Did the initial start up - but end up with a black monitor and the cursor in the top left corner of the monitor.

Any idea what has happened?

Optimist - 09 Feb 2004 10:41 - 1307 of 11003

Timeliner

What O/S?

Timeliner - 09 Feb 2004 11:05 - 1308 of 11003

WinXP Prof

Optimist - 09 Feb 2004 11:18 - 1309 of 11003

Timeliner

What do yo mean by the initial startup?

Is it starting to load the O/S or does it stop before that?

Timeliner - 09 Feb 2004 11:22 - 1310 of 11003

It takes an age to load the operating system, before giving the blank screen/cursor.

Might be the operating system which is a bit low - P2 Celeron 350 with 384 mb ram.

Optimist - 09 Feb 2004 11:30 - 1311 of 11003

I have seen this before and never fully sorted it.

Try loading in safe mode and make a note of the names of any drivers that it hangs on. Also try loading the last good configuration.

Timeliner - 09 Feb 2004 11:36 - 1312 of 11003

Thanks Neil.

Been a bit hectic this morning - and going out shortly for birthday meal at Skegness but will try when we get back.

Thanks

Chris

hilary - 09 Feb 2004 14:14 - 1313 of 11003

Please can somebody tell me how to adjust the time on Windows ME so that it displays on the bottom right of the toolbar as a 24 hour clock rather than a 12 hour clock?

Optimist - 09 Feb 2004 14:26 - 1314 of 11003

Hilary

It's in Regional and Language options in the Control Panel

DocProc - 09 Feb 2004 14:27 - 1315 of 11003

Control Panel

Regional and Language Options

Regional Options Tab
Standards and formats
Customise
Time

To - Do this

Display time in a 24-hour format - Type uppercase H or HH for the hour

Display time in a 12-hour format - Type lowercase h or hh for the hour

Display leading zeros in single-digit hours - Type two characters, HH or hh
Suppress the display of leading zeros in single-digit hours, minutes, or seconds - Type a single uppercase H, or lowercase letter, such as h, m, or s

Display a single letter to indicate AM or PM - Type lowercase t
Display two letters to indicate AM or PM - Type lowercase tt
Display text - Type single quotation marks (') around text

Hope that helps.

hilary - 09 Feb 2004 14:39 - 1316 of 11003

Many thanks guys. That had been driving me round the twist for absolutely ages.

Ironically, I'd seen the Regional options menu but hadn't realised what the difference was between the upper and lower case H.
Register now or login to post to this thread.